Weighing & Force

Shelf, Printer, Scalemate Assembly, SST

Two-roll film capacity • Standard 115 V power supply • Solid-state controlled film cut-off rod • All stainless steel construction • Fully welded wrapper frame • Adjustable, oversized stainless steel foot pads to ensure positive leveling on uneven floors • Stretch film, 19 inch maximum width • Easy-to-use film selector system • Adjustable film tension • Models and accessories to fit any scale

Indicator, Convertor SCT10-AN, 12-24VDC, Analog Output, and RS485/232 Serial Port DIN Mount, SCT-10

Quickly convert digital weight to analog data with the SCT-10 signal transmitter. Theoretical, real-weigh and linearity calibration allow operators to easily calibrate connected scales remotely. A compact display provides weight, configuration, calibration and error conditions to monitor load cell performance constantly. • Converts digital weight to analog output • Sums four input channels in parallel • Theoretical calibration, real-weigh calibration, linearity calibration • Push-button or preset tare • Full-scale analog output with zero setting and PLC correction of analog signal • Displays weight, configuration, calibration and error conditions • DIN-rail mounting, suitable for back panel • Two digital inputs, two digital outputs • Supports ASCII or Modbus RTU protocols

Indicator, SCT1100-AN 12-24VDC and, RS485/232 Serial Port, Analog Out DIN Mount, 4 load cell input. Regulatory modes.

The SCT-1100 can be utilized as an independent or dependent four-channel weight transmitter for direct readings of connected load cells, ensuring accurate results. Easily read net, gross and tare weights of products passing over scales with an efficient signal conditioner. • Up to four independent scales or four load cell inputs • Quick menu for real and theoretical calibration • Red LED display • DIN rail mountable • Configurable calibration and setup parameters from keyboard • Calibration using linearization points • Reading of the net, gross and tare weights, clearing, semi-automatic and preset tare, scale switch, setting of outputs application thresholds • Diagnostic information via serial port, message display, printing, setting of APW in counting mode, digital input for key press • Modbus RTU or ASCII protocol • Easy configuration with Rice Lake Tools software

Indicator, SCT2200 12-24VDC, and RS485/232 Serial Port, DIN Mount, Regulatory Modes.

The SCT-2200 is a small weight transmitter that makes a big difference. It monitors data from up to 16 transmitters and displays results on a 0.3-inch screen. With remote access and touch-free control, operators can use a mobile device or PC to perform calibrations and view data. • HUB mode connects up to 16 transmitters to one fieldbus • Two RS-485 port for "daisy-chain" network connection • Quick menu for real and theoretical calibration • Remote access through web browser for weight monitoring and calibration over EtherNet/IP, PROFINET and Modbus TCP network • Red LED display • DIN rail mountable • Calibration using linearization points • Reading of the net, gross and tare weights, clearing, semi-automatic and preset tare setting of outputs application thresholds • Diagnostic information via serial port, message display, printing, simulation of key pressure, Modbus RTU or ASCII protocol • Printer management on second serial port available • Multi-range function allows for subdividing the scale capacity in two, each up to 3,000 divisions • Easy configuration with Rice Lake Tools software

Indicator, SCT30-AN, 12-24VDC, Analog Output, and RS485 Serial Port DIN Mount, Displays mV and Analog Output Signal Only. Does Not Display Weight.

The SCT-30 is a DIN-rail mountable solution held in a cabinet or control panel to convert load cell signals to analog output. With a digital rotary for zero, tare and setpoint entry, this weight transmitter is simple to setup, calibrate and operate. • LCD display • Powers up to eight (350 ohm) load cells in parallel (with a 24-bit A/D converter) • A/D converter 24-bit 4.8 kHz • 16-bit analog output: 0-20 mA, 4-20 mA, 0-5 V, 0-10 V, ±5 V and ±10 V • Mounting on Omega/DIN rail for back panel or junction box • Diagnostic message for load cell disconnect and over-capacity errors

Scale, SD-1150-WP 1000 lb Package (Scale, Handrail, Indicator, Pit Frame) 36 in(W)X 36 in(L) X 3 in(H) With Smooth Top Anti Slip Rubber Surface, Side Access Junction Box, 36 in(H)X 30 in(W) Steel Painted Handrail And Mounting Hardware. Indicator. 10 ft Homerun Cable With Connector For Indicator. 36 in. x 36 in. Pit frame. Includes 6 AA size Alkaline batteries.

Package includes scale, pit frame, handrail and indicator • Large LCD display • Antimicrobial keypad • Heavy-duty mild steel construction • Live handrail for accuracy and patient safety • Unit of measure toggle or locking • Motiontrap movement compensation technology • EMR capable • Serial and USB data communication ports • Wireless personal area network (WPAN) option available • Tare function • Hold function • Body mass index (BMI) function • Factory calibrated

Power Supply, Voltage Regulator MCR150 63-13-115-6

Automatic overload protection • Convenient lighted on/off switches • Available in 70, 150 and 250VA outputs • Offered in standard 120 volt, 60 Hz models • Two duplex receptacles allow several pieces of equipment to economically share the same source of regulated power

UPS, SOLA SSW1000, 1000VA 120V

Protects against most adverse power conditions, including: frequency variations, surge, noise, blackouts, lightning, spike, brownouts, and over and under voltages • Data-line surge protection for phone or network included on every unit • Greater uptime with intelligent power management, full-sequence battery testing and two-level overload protection

Bag, Static Shielding 8x10

OTR-IMS, Single Direction In-Motion Single Draft Truck Scale Control System Single Direction Configuration, Remote Display, Doppler Radar, Mounting Hardware and Cable

These calculators can be used to determine maximum speed when crossing the scale, estimated fuel savings and estimated increase in transaction capacity when using the SURVIVOR OTR-IMS. • Single-draft weighing • Weigh vehicles in motion up to 6 miles per hour • 1280 Enterprise Series indicator with V2.05 software • LaserLight3 remote display • DOT-grade speed sensor • Software records vehicle ID and gross weight • Compatible with new or existing SURVIVOR OTR truck scales • Patent pending design

Weight Cart, 500-1,000 lb Steel And Tire Assembly Painted

Scale, RL1200IS Elect. Conversion 882IS Indicator with battery pack and charger, 1000 x .5lb, NTEP III The 882IS is designed and approved for use in specific Hazardous (classified) areas by Factory Mutual (FM). These areas are classified by the NFPA70, National Electric Code (Article 500) as: Class I, II, III Divisions 1 or 2 and Groups ABCDEFG T4 and Class I, Zone 0 AEx/Ex ia IIC T4 Ga Zone 21 AEx/Ex ib IIIC T135C Db Ta = -10C to 40C(14F to 104F) and ATEX/IECEx II 1G Ex ia IIC T4 Ga II 2 D Ex ib IIIC T135C Db it is the responsibility of the reseller to keep a permanent traceable record of the location (end user) of the Equipment or return a completed Rice Lake Weighing Systems "Hazardous Area Classification Form" signed by the reseller and users hazardous(classified) area defining authority for our acceptance and permanent record. Proper specification, installation, operation and service of this equipment to National and Local regulations are the responsibility of the end user. Any field modifications of the product voids any and all warranty and FM Approval.

NTEP Certified • 1,000 lb capacity • Conductive wheels to eliminate static buildup and discharge • Handle for ease of portability

Load Cell, CSR T2P1-20K 20,000lb 35ft 2mv/v 350 Ohm FM EW Epoxy HS Tension BLH

Load Cell, DEB 9323-B10- 50k 50000lb 30ft RTI 3mv/v 700 Ohm WW NTEP IIIL 10 M FM SST

Load Cell, DEB 9423-B10- 50k-30P1 50000lb 30ft RTI 3 mv/v 700 OHM WW NTEP IIIL 10M SST

Load Cell, SEB 65023A1k- 5107-10 1,000lb 10ft Senstrs 3mV/V 350 OHM WW NTEP III 5 FM

Load Cell, SEB 65023A1K- 5507 1000lb 10ft SENSTRS 3mv/v 350 Ohm WW NTEP III 5M FM IP67 Low Profile

Load Cell, DEB 65040A50K- 1127W 50,000lb 40ft Sensortr 3mv/v 700 ohm WW NTEP IIIL 10M FM IP67 WS

Load Cell, DEB 65061A50K- 1108 50000lb 60ft 3mV/V 700 Ohm WW NTEP IIIL 10M IP67 alloy steel

Load Cell, CSR 65114S50K- 1000H 50000lb 35ft Sensortronics 2mV/V 1000 Ohm WC SST HS IP68 NTEP IIIL 10M

Load Cell, SPT 1240-200kg 3.1M TH 2mV/V 350 OHM FM SST IP64

EW-150i Toploader Balance, 30/60/150g x 0.01/0.02/0.05g, 120V adapter

Backlit weight display • Remote zeroing • Easy-to-install NiCAd battery option • RS-232 interface for connecting to printer or PC • Triple range

Gemini GR-202 Semi-Micro Balance, 210g x 0.1mg and 42g x 0.01mg, 120 V adapter

GLP/GMP/GCP/ISO compliant software outputs the calibration data and ID number of the balance for calibration confirmation to the AD-8121B printer • Easy-access door system • Automatic self-calibration • Data memory function • Weighing chamber • Internal adjustment weight • Liquid crystal display (LCD) • RS-232 interface for connecting to printer or PC • WinCT communication tools software • Underweigh hook

Orion HR-300i Analytical Balance, 320g x 0.1mg, RS-232C, 120-230V auto- ranging adapter

GLP/GMP/GCP/ISO compliant software outputs the calibration data and ID number of the balance for calibration confirmation to the AD-8121B printer • System diagnostics to alert the operator of abnormal weighing conditions • RS-232C bidirectional interface (option for HR-60, HR-120 and HR-200; standard for HR-300i and HR-202i) • Weighing chamber • Liquid crystal display (LCD) • WinCT communication tools software • Underweigh hook